Wall Protection FAQs

Find answers to specific product category, safety, design, and environmental questions.

  • 4', 8' and 10' (1.2m, 2.4m and 3.0m) are standard heights, with any size up to 20' (6.1m) being available for most Acrovyn models. Contact your local CS representative regarding longer length requirements. Be sure to reference the available heights for specific model(s) of interest.

  • For model FSC-25N, the maximum height without a seam is 9'6" (2.9m). For model SSM-25MN, the maximum height without a seam is 10' (3.0m). Renaissance™ wood corner guards are supplied cut-to-size only with a standard maximum height of 10' (3.0m). Contact your local CS representative regarding longer length requirements. Be sure to reference the available heights for specific model(s) of interest.

  • Acrovyn Corner Guards are available in most degrees for both surface mounted and flush mounted models. For surface and flush mounted corner guards, angles are 45-160°. For stainless steel and aluminum corner guards, angles are 45-178°. For wood corner guards, angles are 45-179°. Consult your local CS representative with specific requirement.

  • The end/bottom cap prevents the cover from slipping down.

  • It is recommended that all corner guards start at the top of the cove base height to facilitate floor cleaning.

  • Yes. Surface mounted corner guards, models SSM-25N and SSM-15N, can be field modified to accommodate most end wall widths. Surface mounted stainless or aluminum and flush mounted end wall guards are custom fabricated to specified end wall widths.

  • We recommend that they be applied with screws because adhesive or double-sided tape will show through the unit and could yellow over time.

  • No. These corner guards are supplied with the double-sided mounting tape only. This foam tape fills the void between the wall and kickback bend.

  • The FSC-25N is available 3 1/8-12" (79.4-304.8mm). Additional size requirements can be reviewed by your local CS representative to determine feasibility.

  • Our flush retainer sits on the finished floor and has a standard snap on aluminum base to allow the cove base to be installed over it. Specify desired height of the snap on aluminum base.

  • No. However, a two-hour fire rating can be achieved by installing an extra layer of 5/8" (15.9mm) drywall behind the fire rated flush mounted corner guard retainer. For more information, refer to the installation instructions or contact your local CS representative.

  • Yes. All interior wall protection products are supplied with fasteners appropriate for the installation. Steel stud and gypsum is considered standard wall construction. Be sure to specify other wall conditions if applicable. Use of other fasteners will void the product warranty.

  • Yes. Renaissance wood will be shipped pre-finished only. Custom finishes are also available.

  • The LG-034 is not predrilled with holes, but we do supply it with screw nails. We supply 6 nails for 4' (1.2m), 8 nails for 8' (2.4m) and 16 nails for 10' (3.0m). The spacing will be determined by the installer and the nails can be used without predrilling holes.

  • CS offers thermoformed corners that can be used in lieu of trim.

  • The corner guard and all fasteners and end caps needed for installation.

  • Acrovyn Crash Rails are supplied in lengths up to 20' (6.1m) or cut-to-size as required. Renaissance™ wood rails will be shipped in random lengths from 7-12' (2.1-3.7m) unless ordered cut to size [exceptions: max length is 11' (3.4m) for Beech and 8' (2.4m) for Bamboo]. When ordering cut-to-size, material will be supplied in largest single pieces available per current inventory to yield minimal splicing.

  • We can’t recommend an alternative fastener for this condition. Crash rail fasteners are available for walls constructed of minimum 20-gauge steel studding or steel strapping, wood studs, concrete block, concrete masonry unit or equivalent at the specified fastener spacing. When fastening to alternate wall construction, i.e. mullions, it is up to the customer to work with the supplier of the alternate wall construction to determine if it is equivalent/capable of supporting the impact forces incurred by a crash rail and the proper mounting fasteners.

  • Measurements need to be provided to a 1/16" (1.6mm) tolerance.

  • Accuracy is essential because there is no allowance for adjustment.

  • Most crash rails are available with factory-fabricated corners for odd angles. For more information, refer to the crash rail model options or contact your local CS representative.

  • Yes. Some crash rails can be factory radiused to a field-supplied template. For more information contact your local CS representative.

  • Yes. All interior wall protection products are supplied with fasteners appropriate for the installation. Steel stud and gypsum is considered standard wall construction. Be sure to specify other wall conditions if applicable. Use of other fasteners have not been tested and will void the product warranty.

  • Yes. Touch-up markers and fill-sticks are available for standard and custom finishes.

  • 10' is the longest material length. However, if longer runs are necessary the material can be spliced in the field. For all other questions please refer to the installation instructions found on the website or contact your local CS representative.

  • All models have a standard 2" (50.8mm) radius and 30" (762.0mm) on center bracket spacing. For special requirements or dimensions, please contact your local CS representative.

  • Length and width tolerance is +/- 1/16" (1.6mm).

  • No. Typically kick plates are 28-46" (.7-1.2m) in height and width [kick plates should be ordered 2" (50.8 mm) narrower than actual door widths]. Push plates are generally 16-20" (406.4-508mm) in height, by 4-6" (101.6-152.4mm) in width. Kick/push plates can be fabricated to your exact dimensions.

  • Kick/push plates are available in .040" (1.02mm) and .060" (1.52mm) thick Acrovyn, as well as 16 GA. stainless steel.

  • Yes. Custom waves and shapes can be created from .040" (1.02mm) and .060" (1.52mm) Acrovyn. Contact your local CS representative for design possibilities.

  • The entire door and frame can be clad with Acrovyn and still retain the door rating. Intertek certification has been achieved for the full height when Acrovyn is applied with the Fast bond 30 contact adhesive or double-sided tape. (Note: Door frame protection is only available in .040" thickness, and not in 060" thickness.)

  • A label is automatically supplied on the back side. At the customer's request, a mark can be made on the exposed face of all cladding with a heat stamp showing a company identifier and the Intertek symbol.

  • For Acrovyn products, the required cutouts are made in the field with a utility knife.

  • There are several standard door frames in the industry; accurate field measurements help ensure the correctly sized door frame protection is supplied. A door frame sample will be supplied for checking the dimensions and fit (+ 1/16" tolerance).

  • The best way to measure the frame is by using a caliper and noting the dimensions on a CS supplied tear sheet.

  • Request a small sample of .040" (1.02mm) or .060" (1.52mm) material from your local CS representative. Hold the sample against the door frame, then close the door to verify that the sufficient clearance exists. Be sure to check clearance at various places from the bottom of the door and the frame up to the point where the protection terminates, as clearance varies depending upon how straight the door and frame are.

  • On non-fire rated doors, edges of the door can be undercut to compensate for material thickness. (Note: Undercutting fire rated doors will void the fire rating.)

  • Measure the outermost dimensions of the hardware to help determine which doorknob protector has the appropriately sized/shaped opening.

  • A foam roller or brush will be required to apply the supplied Fast bond 30 contact adhesive. Roller and brush are not supplied

  • The Fastbond 30 Contact Adhesive is NOT freeze/thaw stable and is UNUSABLE if frozen. Contact your local CS representative to order additional adhesive.

  • Acrovyn rails are supplied in lengths up to 20' (6.1m) or cut-to-size as required. Renaissance™ wood rails will be shipped in random lengths from 7-12' (2.1-3.7m) unless ordered cut-to-size [exceptions: max length is 11' (3.4m) for Beech and 8' (2.4m) for Bamboo]. When ordering cut-to-size, material will be supplied in largest single pieces available per current inventory to yield minimal splicing.

  • We can’t recommend an alternative fastener for this condition. Our handrails are designed to meet the loading requirements of most building codes which require a minimum of 200 lb. concentrated loading. Handrail fasteners are available for walls constructed of minimum 20-gauge steel studding or steel strapping, wood studs, concrete block, concrete masonry unit or equivalent. When our handrails are installed properly they will meet or exceed most building code requirements; however, when fastening to alternate wall construction, i.e. mullions, it is up to the customer to work with the supplier of the alternate wall construction to determine if it is equivalent/capable of supporting the loads incurred by a handrail and the proper mounting fasteners.

  • Measurements need to be provided to a 1/16" (1.6mm) tolerance.

  • Most handrails are available with factory-fabricated corners for odd angles.

  • Yes. Some handrails can be factory radiused to a field-supplied template.

  • Yes. All interior wall protection products are supplied with fasteners appropriate for the installation. Steel stud and gypsum is considered standard wall construction. Be sure to specify other wall conditions if applicable. Use of other fasteners will void the product warranty.

Yes. For more information, refer to our handrail model options to specify the correct model.

  • Yes. Wood handrails will only be shipped pre-finished. Custom finishes are also available.

  • Yes. Touch-up markers and putty sticks are available for standard and custom finishes.

  • CS can provide a ligature resistant mounting bracket for most handrail models.

  • Minimum lengths for handrails vary by model and can be found in our installation instructions. All handrails are load tested using two mounting brackets, thus the smallest section of handrail installed must use at least two mounting brackets. Contact your local CS representative for availability.

  • Local codes will determine the height at which the handrail is installed.

  • Handrail cover, retainer, bracket, and mounting fasteners

  • An engineered PETG that is free of PVC, phthalates, persistent bioaccumulative toxins (PBT) and bisphenol A (BPA). It has a contemporary texture for improved aesthetics and cleanability and is available in variety of Woodgrain simulated patterns and Acrovyn solid colors. A Cradle to Cradle Certified™ product, it has earned UL® Class A/1 fire rating and meets industry impact strength and fungal resistance tests standards.

  • In addition to Acrovyn 4000 wall protection, CS offers a line of Renaissance™ Real Wood and Metal Products. The Renaissance wood collection has linear profiles and wall panels available in a variety of species and finishes. Wood wall panels have a Class A/1 fire rated particle board core covered in wood veneer. FSC certified wood is available upon request. The Renaissance metal collection has aluminum and stainless steel linear profiles available. Powder coat finishes are also available. Renaissance models are Cradle to Cradle Certified™ Silver or Gold, depending on species and finish selected.

  • Building Product Disclosure and Optimization - Material Ingredients -
    • Option 1 - Material Ingredient Reporting (1 point) / Use at least 20 different permanently installed products from at least five different manufacturers. Acrovyn products certified under Version 3.1 of the Cradle to Cradle Certified™ Product Standard at Silver or Gold meet the credit requirements.
    • Option 2 - Material Ingredient Optimization (1 point) / Use at least 25%, by cost, of the total value of permanently installed products in the project. Acrovyn products certified under Version 3.1 of the Cradle to Cradle Certified™ Product Standard at Silver are valued at 100% of cost and at Gold are valued at 150% of cost.
    • Leadership Extraction Practices - Products with recycled content (aluminum, stainless steel, and composite wood), FSC wood and rapidly renewable Bamboo meet this credit requirement.
    • Indoor Environmental Qualities -
      • Specified adhesives comply with SCAQMD Rule 1168 requirement of LEED for
    • Healthcare.
      • Products tested to be in compliance with California Department of Public Health (CDPH) Standard Method v1.1-2010 are available.
      • Composite woods comply with ULEF and NAF standards.
    • Contributions vary by product, model and finish. For specific product details, call CS at 800.233.8493.

  • Material Ingredient Red List - Acrovyn and Renaissance products certified under Version 3.1 of the Cradle to Cradle Certified™ Product Standard with a Material Health Score of Silver or higher are likely to comply with the LBC Red List because they are inventoried to at least 100ppm. The Cradle to Cradle Certified™ Products Program uses an assessment protocol similar to the Red List.
    • For written confirmation and additional ingredient disclosure, call CS 800.233.8493.
      Certified Wood - FSC-certified wood can be specified.
    • Contributions vary by product, model and finish. For specific product details, call CS at 800.233.8493

  • The Cradle to Cradle Certified™ Product Standard is a multi-attribute, third-party certification. Products are assessed based on five key attributes:
    • Material Health: Each homogeneous material is inventoried, screened, assessed, and optimized down to 100 ppm.
    • Material Reutilization: Products are designed for the technical or biological cycle and nutrient management strategies are in place so materials can be perpetually cycled.
    • Renewable Energy and Carbon Management: Electricity and direct on-site emissions are off set.
    • Water Stewardship: Responsible water consumption and conservation measures are in place at the manufacturing facility and down the supply chain.
    • Social Responsibility: Products have material-specific/issue-related audit/certification; supply chain social issues are investigated and improved; and the company has an active innovative social project.
    • The standard provides a holistic continuous improvement platform for product development.
    • Depending on certification achievement level, the certification can qualify products for LEED® v4 MR Option 1 & 2.

  • Cradle to Cradle Certified™ levels achieved are based on the lowest assessment level of model variations and finishes selected. In some cases, there are non-certified model variations that are exceptions to current certifications. Each unique product ordered will need to be evaluated against current certifications to determine its certification level.

  • No. However, while Acrovyn 4000 is not GREENGUARD or SCS certified, it does meet the requirements of their test standards. VOC Emission Test Certificates for compliance to California Department of Public Health CDPH/EHLB/Standard Method Version 1.1, 2010 (Emission testing method for CA Specification 01350) are available on our website for specific models.

  • No. However CS continues to review the evolution of bio-based compounds for potential use in future generations of Acrovyn. We believe additional research and discernment is necessary before the use of biopolymers can be accepted as a socially, ethically and environmentally sound practice. Until then, we will continue to use only those raw materials that have been sourced responsibly.

  • Yes. We believe in most situations, recycling building material within our customers' local areas is more cost effective and environmentally friendly. If you need assistance in identifying the version of Acrovyn material or locating a local plastic recycling service, call CS at 800.233.8493.

  • No. However, it is resistant to growth of bacteria in accordance with ASTM G22-75, Standard Practice for Determining Resistance of Plastics to Bacteria. Acrovyn 4000 demonstrated no Fungal Growth in accordance to ASTM G21-96, Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi. Taking into consideration that it does not promote growth of some of the most common and most harmful bacteria and fungi found in healthcare facilities, it was decided not to add antimicrobial agents to the Acrovyn 4000 line. CS endorses regular cleaning according to the Acrovyn Wall Protection Systems Care & Maintenance Instructions to combat the spread of germs on hard surfaces.

  • In 2003, the Centers for Disease Control and Prevention (CDC) concluded that, “No evidence is available to suggest that use of these [antimicrobial] products will make consumers and patients healthier or prevent disease. No data supports the use of these items as part of a sound infection control strategy.” With no evidence indicating that antimicrobials prevent disease, avoiding these chemicals of concern is becoming the industry standard led by guidelines set forth in the Healthier Hospitals Initiative, The Living Building Challenge™, LEED® v4 and others.

  • CS follows the precautionary principle, avoid product or processes whose environmental and human health effects are disputed or unknown. PVC contains additives - vinyl chloride monomers, halogenated/brominated fire retardants, plasticizers and other materials - that have all been proven to be harmful at some point along their lifecycle. The environmental concerns of PVC have led numerous organizations and authorities in the US and European countries to discourage or ban its use. Dioxin, a PBT toxin that can be emitted during manufacturing and disposal of PVC, is among the top offenders on EPA’s list of toxic chemicals.

  • Persistent bioaccumulative toxins are chemicals that remain in the environment and pose risk to human health and ecosystems. They are a threat because they do not break down easily in the environment, which is why they are described as persistent, and they can build up in the food chain over time or bioaccumulate. PBTs are known to cause damage to the human nervous and reproductive systems.

  • The chemical bisphenol A is a known endocrine disruptor that has a multitude of health concerns: obesity, diabetes, problems with fertility and reproductive organs, various cancers and cognitive/behavioral deficits. BPA is residual in polycarbonate plastics; since Acrovyn 4000 is PETG instead of a polycarbonate, there is no BPA residuals in the plastic.

  • Yes. ISO 14001 is the most widely recognized international standard for responsible environmental management. It is CS' environmental management system that audits CS for ongoing compliance with the Environmental and Chemicals Policy.

  • Architects, designers and owners seek to make informed decisions when they fabricate, specify, install, use and dispose of building products. There are building products that are harmful to humans and the environment; by disclosing environmental and health impacts, it allows our customers to select optimized alternatives.

  • Transparency labels and website - Many of CS' products have an on-product label that discloses the product's ingredients and environmental impacts. This label was designed in partnership with Perkins & Will as a way to conveniently put sustainability information right into the hands of customers. Resulting from a collaborative partnership with Perkins & Will, CS created the first on-product label that discloses the product's ingredients and environmental impacts.

  • Yes. Acrovyn is UL® Classified and Labeled or Intertek Labeled. The following list states the six distinctly different applications for Acrovyn
    1. Acrovyn Profiles (handrails, crash rails, bumper guards, accent rails and corner guards) - UL Classified and Labeled Class A/1
    2. Acrovyn Fire Rated, Flush Mounted, Corner Guards are UL Labeled with one-hour and two-hour installation
    3. Acrovyn Wall Covering - UL Classified and Labeled Class A/1
    4. Acrovyn Wall Panels and Dimensional Moldings Wall System - UL Classified and Labeled Class B/2 (Complete system test in lieu of individual component test)
    5. Acrovyn Door Protection is Intertek Labeled for 20-minute wood fire doors (particle board core with wood stiles and rails, surface mounted or concealed intumescent required) and 60-minute wood mineral core fire doors with non-combustible stiles and rails (surface mounted or concealed intumescent required).
    6. Acrovyn Door Frame Protection is Intertek Labeled for 60-minute standard steel UL Subject 63 fire door frames (intumescent edge seal required).

  • Class A/1 designates the material's surface burning characteristics when tested in accordance with UL723, ASTM E84 and CAN/ULCS102.2. The governing building codes such as IBC, NFPA, UBC, BOCA and SBCCI mandate that all building materials meet the minimum of a Class C/3 rating. Time-hour rating is the appropriate designation for those products applied onto or into equally rated doors, as well as fire rated flush mounted corner guards installed in fire rated walls. Applying a material that is not time-rated to a fire rated door and/or door frame will negate the rating of the assembly.

  • The Underwriters Laboratories label signifies that each piece of Acrovyn constantly meets or exceeds the requirements of the specified test procedure and outcome. CS products that are classified and labeled are part of the UL Follow-Up Program, which ensures we continue to use classified materials and components.

  • They are identified with official labeling and/or stamping on the products' packaging and/or on the ordered product.

  • The wall panels are constructed using a 3/8" (9.5mm) substrate laminated with .040" (1.02mm) PVC-free rigid sheet. For wrapped edge panels, the edges of the panel are folded back to the designated panel thickness. For the demountable Sure Snap™ System, a shallow box is created to conceal the mounting hardware by either the folded panel edge or the trims.

  • Yes. Demountable Sure Snap panels can be 3/4" (19.1mm) (standard), 1" (25.4mm) and 2" (50.8mm) deep. Permanent adhesive panels are 3/8" (9.5mm) deep only.

  • The 3/8" (9.5mm) permanent adhesive panel is 47" x 119" (1.2m x 3.0m), the 3/4" (19.1mm) demountable Sure Snap panel is 46" x 118" (1.2m x 3.0m), the 1" (25.4mm) demountable Sure Snap panel is 45.5" x 117.5" (1.2m x 3.0m) and the 2" (50.8mm) demountable Sure Snap panel is 43.5" x 115.5" (1.1m x 3.0m).

  • Yes. Picture frame and thin trims are available in different depths. However, they are only available for the standard panel depths: 3/8" (9.5mm) for permanent adhesive and 3/4" (19.1mm) for the demountable Sure Snap System.

  • Yes. Please contact your local CS representative with your specific project needs.

  • Acrovyn solid color pattern panels are UL® Classified and Labeled Class B/2. Acrovyn by Design® wall panels are tested in accordance with ASTM E-84 for Class B/2.

  • Yes. The wall panels can be used throughout any building that is protected by an automatic sprinkler system except for Group I-3 structures. These structures include, but are not limited to, correctional centers, detention centers, pre-release centers and prisons.

  • Yes. There is a moisture barrier applied to the backside of the wall panels and the edges of the panel returns are sealed.

  • No, not at this time. However, Acrovyn by Design® can be used to print custom texture images on wall panels.

  • CS can supply wall panels based on the sizes and quantities a customer provides, therefore not all wall panel orders will require drawings from drafting. However, drafting services can be provided for custom shape panels and/or layouts with no additional charge.

  • Yes. The wall panels can be installed in elevators, but this requires permits and additional paperwork that are beyond normal CS business practices. Consult your local codes/office for specific details of your project requirements before ordering. The wall panels weigh approximately two pounds per square foot.

  • We supply permanent construction adhesive or the demountable Sure Snap System to install the wall panels.
    • For more information, refer to the permanent adhesive and Sure Snap demountable installation instructions.

  • A small tolerance is designed in the demountable Sure Snap wall panels to allow for easy installation over the typical irregularities of wall construction. These gaps will vary in depth depending on the smoothness of the wall surface. These areas are unavoidable and will have to be handled at the discretion of the architect, designer and/or owner.

  • Drafting layout of Wall Panels (if applicable), wall panels with factory installed female snaps, male snaps, center points, drywall anchors, #6 X 1-5/8" (41.3mm) Phillips bugle head tek screws and fill-sticks are included. There are suction cups, aluminum splice plates, Acrovyn sheet or aluminum reveal strips, panel reveal spacers, horseshoe shims primer and loose trims available for purchase as well.

  • To evenly space wall panels, use panel reveal spacers, which are available for purchase.

  • The wall panels can be installed over flat surfaces such as ceramic tile, block and painted or vinyl clad drywall.
  • Shimming is sometimes necessary when installing over drywall, therefore, horseshoe shims are available for purchase. The use of our demountable Sure Snap System allows panels to be easily removed for maintenance or access.

  • Yes. Outside corner guards are available. Inside corner guards are not available at this time.

  • We recommend starting installation in the middle of the wall at the floor level and working your way left, right and up. For more information, refer to the permanent adhesive and Sure Snap demountable installation instructions.

  • Yes. Female snaps are factory installed unless the panels are being installed over a hard surface such as tile or concrete (which must be specified). The mounting hardware can be removed and relocated for any field modifications. For more information, refer to the “Moving Snaps” section of the installation instructions.

  • No. The system is designed to be installed directly to the drywall. It is not required to hit a stud with the fasteners. No additional reinforcement of the wall is required.

  • Generally, the spacing will be 24" (609.6mm) maximum both vertically and horizontally between the mounting hardware. This will vary with panel size and will be determined by the layout drawings.

  • Yes. The snaps can be relocated. For more information, refer to the “Re-marking the Wall Fastener Locations” section of the installation instructions.

  • Yes. Picture frame and thin trims are factory installed to the demountable Sure Snap wall panels (not the walls) to create an easier, faster installation experience. Permanent adhesive wall panel trims can be specified as loose or separate and then shipped.

  • No. If installed properly, the mounting hardware can be easily disengaged and re-engaged without damaging the wall. Suction cups can be used to assist with the removal of the panel, which are available for purchase.

  • Yes. Clear anodized trims are standard, but they can be color-match painted to a customer supplied sample for an additional charge.

  • Yes. However, the wall covering variation must be specified when ordering because the back side notch on the base and wainscot trims must be adjusted for the difference in thickness.

  • No. For wainscot applications, the adhesive should be applied above the top edge of the wall covering to allow the horizontal wainscot trim to be fastened directly to the wall. For vertical and other horizontal trims, there should be a 1" (25.4mm) gap between the sheets to ensure the trims are adhered directly to the wall.

  • The Dimensional Molding Wall System was designed with variable trim thicknesses to allow for a “step down” approach to avoid exposure of cut ends on trims.

  • No. Brad nails should not go through the wall covering. Doing so will trap the wall covering, prohibiting proper expansion and contraction necessary for a successful installation.

  • Yes. We offer 90° and odd degree outside corner plinth blocks for end treatments and transitions.

  • The M1 Structural Adhesive has unlimited freeze/thaw cycles. Keep at room temperature until completely thawed and consistent.

  • It is .040” (1.02mm) thick, clear, PVC-free Acrovyn rigid sheet that includes a high resolution image printed behind it. A protective coating is applied to stabilize the image and should not be damaged or removed or it will adversely affect the image.

  • It's available with Suede texture only.

  • No. However, thermoformed outside corners are available (for custom Acrovyn by Design only).

  • Kick plates (non-rated application) and rub strips are available only with custom designs and not with beveled edges. Factory cut-to-size standard patterns in Acrovyn by Design are not currently available. Due to the repeat of these patterns, if cut-to-size material is required, we recommend that the sheet be cut in the field to the desired sizes.

  • Acrovyn by Design is created using an entirely different manufacturing process. Woodgrain film is fused to the front surface of Acrovyn Rigid Sheet; Acrovyn by Design’s image is printed behind clear rigid sheet.

  • Yes. However, not for door cladding applications. It has been tested to the test standards listed below. For additional information, please click here.
    • Meets Class A/1 fire criteria (ASTM E84)
    • Impact & Taber Abrasion Performance
    • Bacteria and fungi resistant

  • No. Our competitors own the copyright to their patterns. However, various options exist, such as using one of our patterns or an image of your own.

  • Refer to the inkjet marking on the backside of sheet or profile.

  • Imagery is available on various sizes. Our standard size is 4'x8' (1.2m x 2.4m) or 4'x10' (1.2m x 3.0m). Wall murals will be comprised of multiple sheets for each image. Sheets will be cut as necessary with no additional cut charge.

  • Yes. Images can be used on wall panels with permanent adhesive or the demountable Sure Snap System.

  • No, if accessing Getty/Istock portal through CS Website for royalty-free graphics.
  • Yes, a signed Acrovyn by Design® Copyright Agreement is REQUIRED if the image is not available through the CS website Getty/I-Stock portal. CS Copyright agreement is needed before the submittal process can begin.

1. In order to maintain pattern alignment and ensure proper layout of the design, it is important to dry fit all sheets prior to installation. If installing custom imagery, refer to the drafting details for layout references.

2. Tinted primers can be used at sheet seam locations to match the graphic colors. Doing this in conjunction with applying clear caulk later could help make sheet joints less visible.

3. Trimming of pattern sheets, if required, should be done only at the beginning and the end of a run to ensure pattern alignment. Sheets with imagery should be cut and trimmed as noted on the submittal and drawings. All necessary cutouts should be performed as described in installation instructions.

4. Do not damage or remove the protective coating that is on the back side of the Acrovyn by Design rigid sheet.

  • 4'x8' (1.2m x 2.4m) or 4'x10' (1.2m x 3.0m) sheets only. They are not available as cut-to-size due to the repeat of the pattern. The sheet can be cut in the field to the desired size.

  • Sheet orientation can change, however the pattern direction will not change.

  • Yes. Any of our patterns can be used on wall panels with permanent adhesive or the demountable Sure Snap™ system.

  • An engineered PETG that is free of PVC, phthalates, persistent bioaccumulative toxins (PBT) and bisphenol A (BPA). It has a contemporary texture for improved aesthetics and cleanability and is available in variety of patterns and Acrovyn solid colors. A Cradle to Cradle Certified™ product, it has earned UL® Class A/1 fire rating and meets industry impact strength and fungal resistance tests standards.

  • In addition to Acrovyn 4000 wall protection, CS offers a line of Renaissance™ Real Wood and Metal Products. The Renaissance wood collection has linear profiles and wall panels available in a variety of species and finishes. Wood wall panels have a Class A/1 fire rated particle board core covered in wood veneer. FSC certified wood is available upon request. The Renaissance metal collection has aluminum and stainless steel linear profiles available. Powder coat finishes are also available. Renaissance models are Cradle to Cradle Certified™ Silver or Gold, depending on species and finish selected.

  • Building Product Disclosure and Optimization - Material Ingredients -
    • Option 1 - Material Ingredient Reporting (1 point) / Use at least 20 different permanently installed products from at least five different manufacturers. Acrovyn products certified under Version 3.1 of the Cradle to Cradle Certified™ Product Standard at Silver or Gold meet the credit requirements.
    • Option 2 - Material Ingredient Optimization (1 point) / Use at least 25%, by cost, of the total value of permanently installed products in the project. Acrovyn products certified under Version 3.1 of the Cradle to Cradle Certified™ Product Standard at Silver are valued at 100% of cost and at Gold are valued at 150% of cost.
    • Leadership Extraction Practices - Products with recycled content (aluminum, stainless steel, and composite wood), FSC wood and rapidly renewable Bamboo meet this credit requirement.
    • Indoor Environmental Qualities -
      • Specified adhesives comply with SCAQMD Rule 1168 requirement of LEED for
    • Healthcare.
      • Products tested to be in compliance with California Department of Public Health
    • (CDPH) Standard Method v1.1-2010 are available.
      • Composite woods comply with ULEF and NAF standards.
    • Contributions vary by product, model and finish. For specific product details, call CS at 800.233.8493.

  • Material Ingredient Red List - Acrovyn and Renaissance products certified under Version 3.1 of the Cradle to Cradle Certified™ Product Standard with a Material Health Score of Silver or higher are likely to comply with the LBC Red List because they are inventoried to at least 100ppm. The Cradle to Cradle Certified™ Products Program uses an assessment protocol similar to the Red List. For written confirmation and additional ingredient disclosure, call CS 800.233.8493.
    • Certified Wood - FSC-certified wood can be specified.
    • Contributions vary by product, model and finish. For specific product details, call CS at 800.233.8493 or visit www.acrovyn.com/C2C.

  • The Cradle to Cradle Certified™ Product Standard is a multi-attribute, third-party certification. Products are assessed based on five key attributes:
    • Material Health: Each homogeneous material is inventoried, screened, assessed, and optimized down to 100 ppm.
    • Material Reutilization: Products are designed for the technical or biological cycle and nutrient management strategies are in place so materials can be perpetually cycled.
    • Renewable Energy and Carbon Management: Electricity and direct on-site emissions are off set.
    • Water Stewardship: Responsible water consumption and conservation measures are in place at the manufacturing facility and down the supply chain.
    • Social Responsibility: Products have material-specific/issue-related audit/certification; supply chain social issues are investigated and improved; and the company has an active innovative social project.
    • The standard provides a holistic continuous improvement platform for product development.
    • Depending on certification achievement level, the certification can qualify products for LEED® v4 MR Option 1 & 2.

  • Cradle to Cradle Certified™ levels achieved are based on the lowest assessment level of model variations and finishes selected. In some cases, there are non-certified model variations that are exceptions to current certifications. Each unique product ordered will need to be evaluated against current certifications to determine its certification level.

  • No. However, while Acrovyn 4000 is not GREENGUARD or SCS certified, it does meet the requirements of their test standards. VOC Emission Test Certificates for compliance to California Department of Public Health CDPH/EHLB/Standard Method Version 1.1, 2010 (Emission testing method for CA Specification 01350) are available on our website.

  • No. However CS continues to review the evolution of bio-based compounds for potential use in future generations of Acrovyn. We believe additional research and discernment is necessary before the use of biopolymers can be accepted as a socially, ethically and environmentally sound practice. Until then, we will continue to use only those raw materials that have been sourced responsibly.

  • Yes. We believe in most situations, recycling building material within our customers' local areas is more cost effective and environmentally friendly. If you need assistance in identifying the version of Acrovyn material or locating a local plastic recycling service, contact us or call CS at 800.233.8493.

  • No. However, it is resistant to growth of bacteria in accordance with ASTM G22-75, Standard Practice for Determining Resistance of Plastics to Bacteria. Acrovyn 4000 demonstrated no Fungal Growth in accordance to ASTM G21-96, Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi. Taking into consideration that it does not promote growth of some of the most common and most harmful bacteria and fungi found in healthcare facilities, it was decided not to add antimicrobial agents to the Acrovyn 4000 line. CS endorses regular cleaning according to the Acrovyn Wall Protection Systems Care & Maintenance Instructions to combat the spread of germs on hard surfaces.

  • In 2003, the Centers for Disease Control and Prevention (CDC) concluded that, “No evidence is available to suggest that use of these [antimicrobial] products will make consumers and patients healthier or prevent disease. No data supports the use of these items as part of a sound infection control strategy.” With no evidence indicating that antimicrobials prevent disease, avoiding these chemicals of concern is becoming the industry standard led by guidelines set forth in the Healthier Hospitals Initiative, The Living Building Challenge™, LEED® v4 and others.

  • CS follows the precautionary principle, avoid product or processes whose environmental and human health effects are disputed or unknown. PVC contains additives - vinyl chloride monomers, halogenated/brominated fire retardants, plasticizers and other materials - that have all been proven to be harmful at some point along their lifecycle. The environmental concerns of PVC have led numerous organizations and authorities in the US and European countries to discourage or ban its use. Dioxin, a PBT toxin that can be emitted during manufacturing and disposal of PVC, is among the top offenders on EPA’s list of toxic chemicals.

  • Persistent bioaccumulative toxins are chemicals that remain in the environment and pose risk to human health and ecosystems. They are a threat because they do not break down easily in the environment, which is why they are described as persistent, and they can build up in the food chain over time or bioaccumulate. PBTs are known to cause damage to the human nervous and reproductive systems.

  • The chemical bisphenol A is a known endocrine disruptor that has a multitude of health concerns: obesity, diabetes, problems with fertility and reproductive organs, various cancers and cognitive/behavioral deficits. BPA is residual in polycarbonate plastics; since Acrovyn 4000 is PETG instead of a polycarbonate, there is no BPA residuals in the plastic.

  • Yes. ISO 14001 is the most widely recognized international standard for responsible environmental management. It is CS' environmental management system that audits CS for ongoing compliance with the Environmental and Chemicals Policy.

  • Architects, designers and owners seek to make informed decisions when they fabricate, specify, install, use and dispose of building products. There are building products that are harmful to humans and the environment; by disclosing environmental and health impacts, it allows our customers to select optimized alternatives.

  • Transparency labels and website - Many of CS' products have an on-product label that discloses the product's ingredients and environmental impacts. This label was designed in partnership with Perkins & Will as a way to conveniently put sustainability information right into the hands of customers. Resulting from a collaborative partnership with Perkins & Will, CS created the first on-product label that discloses the product's ingredients and environmental impacts.

  • Yes. Acrovyn is UL® Classified and Labeled or Intertek Labeled. The following list states the six distinctly different applications for Acrovyn
    1. Acrovyn Profiles (handrails, crash rails, bumper guards, accent rails and corner guards) - UL Classified and Labeled Class A/1
    2. Acrovyn Fire Rated, Flush Mounted, Corner Guards are UL Labeled with one-hour and two-hour installation
    3. Acrovyn Wall Covering - UL Classified and Labeled Class A/1
    4. Acrovyn Wall Panels and Dimensional Molding Wall System - UL Classified and Labeled Class B/2 (complete system test in lieu of individual component test).
    5. Acrovyn Door Protection is Intertek Labeled for 20-minute wood fire doors (particle board core with wood stiles and rails, surface mounted or concealed intumescent required) and 60-minute wood mineral core fire doors with non-combustible stiles and rails (surface mounted or concealed intumescent required).
    6. Acrovyn Door Frame Protection is Intertek Labeled for 60-minute standard steel UL Subject 63 fire door frames (intumescent edge seal required).

  • Class A/1 designates the material's surface burning characteristics when tested in accordance with UL723, ASTM E84 and CAN/ULCS102.2. The governing building codes such as IBC, NFPA, UBC, BOCA and SBCCI mandate that all building materials meet the minimum of a Class C/3 rating. Time-hour rating is the appropriate designation for those products applied onto or into equally rated doors, as well as fire rated flush mounted corner guards installed in fire rated walls. Applying a material that is not time-rated to a fire rated door and/or door frame will negate the rating of the assembly.

  • The Underwriters Laboratories label signifies that each piece of Acrovyn constantly meets or exceeds the requirements of the specified test procedure and outcome. CS products that are classified and labeled are part of the UL Follow-Up Program, which ensures we continue to use classified materials and components.

  • They are identified with official labeling and/or stamping on the products' packaging and/or on the ordered product.

  • Yes. An Acrovyn .040" (1.02mm) thick wall covering has a minimum radius of 9" (228.6mm) up to 19" (482.6mm) and must be pre-formed prior to shipping product. An Acrovyn .060" (1.52mm) thick wall covering radiuses up to 24" (609.6mm) and must be pre-formed prior to shipping; any radius dimensions beyond the 24" (609.6mm) for .060" (1.52mm) should be formed in the field.
    • (Note: It is not recommended that our standard or aluminum trims be bent around a radius. This could cause the trims to kink.)

  • No. The back of the Acrovyn has product identifier markings.

  • Yes. The wainscot trim can be used as an edge trim. CS does not figure this style application when wainscot trim is specified for an order. It is the responsibility of the customer to order the additional wainscot trim to be used for this type of application.

  • Beadboard, Dado and Pinstripe textures in both Acrovyn solid colors and Woodgrains can be used.
    • [Note: Textured sheet is 43" (1.1m) wide, not 48" (1.2m), due to the limitations of the manufacturing process.]

  • All Acrovyn cuts can be performed using electric shears, a spiral saw or a utility knife. Several cuts will be required to completely cut through if using a utility knife.

  • CS Acrovyn Interiors Heavy Duty Water-Based Mastic Adhesive and Primer are freeze/thaw stable up to three cycles. CS color-matched and clear caulk is freeze/thaw stable for up to three cycles. CS M1 Structural Adhesive has unlimited/freeze/thaw cycles. The Fastbond 30 Contact Adhesive is not freeze/thaw stable and is unusable if frozen. Adhesive, primer and caulk can be thawed at room temperature until completely thawed and consistent.

  • No. As long as it is a water based primer without PVA (polyvinyl acetate), any primer can be used.

  • No. We only have data available on the chemicals that are listed in the chemical resistance testing results. We recommend you perform a test for adverse effects in a small, discreet area with any chemical that is not on our care and maintenance document. After using any cleaners on the product, be sure to wipe it down with a wet cloth to remove any residue.

  • CS offers thermoformed corners so that the image can continue around a corner condition.

  • Yes. When installing over existing materials like wallpaper or vinyl wall covering, the entire surface must be inspected for areas that are not securely bonded to the wall surface. Any loose areas must be removed and repaired as required. The existing wall covering should then be cleaned with a mild detergent and wiped dry. Be certain all cleaned areas are completely dry before proceeding.
    • Note: CS strongly suggests that a test area be done to ensure desired adhesion is achieved. All adhesive testing is the responsibility of the contractor on-site.

By continuing to browse or by clicking ‘Accept’, you agree to the storing of cookies on your device to enhance your site experience and for analytical purposes. To learn more about how we use the cookies, please see our privacy policy.